High-voltage magnetic track · 25mm catalogue system
25mm high-voltage magnetic track system: rail, parts, heads and controls
This page sets out the printed catalogue for Sampo's 25mm high-voltage magnetic track system: the two-wire rail YZ6805A, six connecting and mounting parts, 28 fixtures and five control devices. Model codes, wattages, beam angles and sizes are given as the catalogue prints them, so you can draft a parts list before you write to us.
The catalogue doesn't identify YZ6805A as our M25 series, and the two shouldn't be read as the same product. The figures below belong to this catalogue build only. If you're also ordering M25, we confirm whether the two are equivalent before any figures are combined, and nothing here carries across to M35 or the 48V tracks.
Printed on every fixture
What the whole 25mm catalogue shares
Each fixture block in the catalogue repeats the same lines for lens, colour rendering, supply and colour temperature. They're listed once here, so the tables further down only carry what changes from head to head.
About the supply figure: every fixture block prints 90–265V. Elsewhere on this site we give 95–260V for the M25 and M35 tracks, a narrower range that sits inside the printed one. For an order built from this catalogue, the printed rating is the one that applies, and we confirm it against the exact models on your list.
Rail · YZ6805A
The rail: one model code, four lengths
The rail is described as a high-voltage two-wire magnetic track. The catalogue prints all four lengths under the same model code, YZ6805A, so we confirm the order code for each length when we quote.
The 25 in the system name matches the printed rail width, W25, with a printed height of H52. The catalogue doesn't print the slot opening, so the fit between a head and the rail is something we check against the fixture list, not something to read off this table.
Three mounting methods are shown for the rail: surface-mounted, embedded in the ceiling, and suspended. The recessed-mount part and the suspension kit below are the parts that go with the second and third.
| Length | Printed size | Finish |
|---|---|---|
| 1.0 m | L1000 × W25 × H52 mm | Black |
| 1.5 m | L1500 × W25 × H52 mm | Black |
| 2.0 m | L2000 × W25 × H52 mm | Black |
| 3.0 m | L3000 × W25 × H52 mm | Black |
Parts
Connecting and mounting parts
Six parts complete the rail: a power header where the supply enters the run, three connectors for joints and corners, and the two parts for recessed and suspended installation. All six are printed in black.
| Part | Model | Printed size | Note |
|---|---|---|---|
| Power header | XYZ25-X | L65 × W25 × H15 mm | Feed lead 350mm |
| Connector with flexible link | XYZ25-L | L65 × W25 × H15 mm | Total length 120mm |
| Straight connector | XYZ25-I | L65 × W25 × H15 mm | |
| L-shaped corner connector | XYZ25-LA | L78 × W78 × H57 mm | |
| Recessed-mount (embedded) part | XYZ25-M | L38 × W60 × H48 mm | For recessed installation |
| Suspension kit | XYZ25-D | Ø60 × H15 mm | Cable 1500mm |
Fixtures · 28 models
Fixture models by family
The heads fall into 14 families, from linear grille and flood bars to spotlights, adjustable-focus spots and pendants. The bar families print a 25mm width, the same as the rail; the round heads are listed by diameter. Read the table by family first, then pick the wattage and length that suit the run.
| Model | Power | Beam | Printed size |
|---|---|---|---|
| Grille light | |||
| YZ2509S | 9W | 24° | L220 × W25 × H41 mm |
| YZ2518S | 18W | 24° | L410 × W25 × H41 mm |
| Flood light | |||
| YZ2509F | 9W | 120° | L220 × W25 × H41 mm |
| YZ2518F | 18W | 120° | L410 × W25 × H41 mm |
| YZ2527F | 27W | 120° | L600 × W25 × H41 mm |
| Corner floodlight | |||
| YZ2518FL | 18W | 120° | L308 × W25 × H41 mm |
| Folding grille light | |||
| YZ2509Z | 9W | 24° | L220 × W25 × H110 mm |
| YZ2518Z | 18W | 24° | L410 × W25 × H110 mm |
| Folding flood light | |||
| YZ2509ZF | 9W | 120° | L220 × W25 × H110 mm |
| YZ2518ZF | 18W | 120° | L410 × W25 × H110 mm |
| Folding die-cast grille light | |||
| YZ25-12Z | 12W | 24° | L220 × W25 × H127 mm |
| Folding die-cast floodlight | |||
| YZ25-12ZF | 12W | 120° | L220 × W25 × H127 mm |
| Track spotlight | |||
| YZ2507DGB | 7W | 24° | Ø40 × L80 mm |
| YZ2510DGB | 10W | 24° | Ø50 × L100 mm |
| YZ2507DG3 | 7W | 24° | Ø40 × L95 mm |
| YZ2510DG3 | 10W | 24° | Ø50 × L115 mm |
| YZ2518DG3 | 18W | 24° | Ø65 × L135 mm |
| Adjustable-focus spotlight | |||
| YZ2510DG1 | 10W | 10–55° | Ø55 × L104 mm |
| YZ2520DG1 | 20W | 10–55° | Ø60 × L130 mm |
| YZ2530DG1 | 30W | 10–55° | Ø75 × L154 mm |
| Double-head spotlight | |||
| YZ2507DG-2 | 9W × 2 | 15° / 24° / 36° | Ø40 × L80 mm |
| Grille spotlight | |||
| YZ2506BS | 6W | 24° | Ø70 × H50 mm |
| YZ2509BS | 9W | 24° | Ø95 × H35 mm |
| Half-moon fill light | |||
| YZ2510DS1 | 10W | 120° | Ø50 × H100 mm |
| Pendant light | |||
| YZ2510DX | 10W | 24° | Ø40 × L300 mm |
| YZ2507DX1 | 7W | 24° | Ø40 × L370 mm |
| YZ2507DX3 | 7W | 24° | Ø70 × H52 mm |
| Half-moon pendant light | |||
| YZ2510DS | 10W | 120° | Ø100 × H100 mm |
Sizes are in millimetres: L length, W width, H height, Ø diameter. Most fixture blocks also print "3 colour changeable and dimmable". Some of the pendant, grille-spotlight and half-moon blocks don't carry that line, so dimming and colour switching are confirmed model by model before we quote.
Controls
Five control devices
The catalogue lists five devices for switching and adjusting the heads: a panel switch, a gateway and a 12-circuit remote on 2.4G, plus a handheld remote and a panel remote on Bluetooth. Two of them share the printed code YZ-YK, told apart only by the link type, so we name both the code and the link in a quotation.
The 12-circuit remote is named as printed, YZ-YK. The catalogue doesn't explain how separate control is achieved on this two-wire rail, so device pairing and control behaviour are confirmed per order. The smart control page covers the wider picture.
| Device | Model | Link | Printed size | Colour |
|---|---|---|---|---|
| Smart panel switch | YZ-KG | 2.4G | L86 × H86 mm | White |
| Double gateway | YZ-WG | 2.4G | L60 × W60 × H15 mm | White |
| 12-circuit remote controller | YZ-YK | 2.4G | L42 × W13 × H142 mm | Black |
| Bluetooth remote control | YZ-YK | Bluetooth | L37 × W18 × H150 mm | Black |
| Panel remote control | YZ-YK2 | Bluetooth | L86 × W90 × H15 mm | Black |
Using this page
From catalogue to parts list
A first list for one ceiling can be built in five lines: the rail lengths for each run, a power header where the supply comes in, the connectors at each joint or corner, the recessed-mount parts or suspension kits if the rail isn't surface-fixed, and the heads by model code. Add a control device if you want to switch or adjust the heads remotely.
Send that list with a ceiling sketch and we'll check it, fill any gaps and quote it.
What the catalogue doesn't print
- The slot opening of the rail, and the conductor and insulator materials.
- Luminous output, IP rating and certification for individual models.
- Separate order codes for the four rail lengths and for the two YZ-YK remotes.
- Whether a white finish is available for each part and head.
- Dimming on the blocks that don't print the dimming line.
We answer these per enquiry, in writing, for the models on your list.
Comparing tracks first? See the M25 and M35 series, compare the 48V family or run the two-question selector.
Next step
Send the ceiling, we'll send the system
A plan or a phone photo of the ceiling, the rough run lengths and the voltage you prefer are enough to start. We reply with a suggested series, the profile and the fixture families that fit.